You will have to bring the ball bearing out using a magnet. If you are facing the issue of the shift not working forward or reverse, it could be because a detent ball bearing may have fallen off during some other work on the transmission. It moves clockwise when you wish to move the cart forward. On the Yamaha G9, the shift lever has a different alignment. Yamaha G9 Golf Cart Shift Cable Adjustment This has been seen to be the better method in the Yamaha G2 You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position.You should thoroughly clean the cable using a spray like WD40.One is the transaxle end and the other end is where you use the handle to shift R and F.The adjustment has to be done at both ends.Allow the engine to cool before you do this exercise.Do this inspection when the golf cart’s engine is off.If it is damaged you must go for a full replacement.Examine the shift cable closely for any damage.If you are only making an adjustment to the shift cable, follow these steps: This helps to ensure that the replacement does not alter the arrangement in the area. Remember to mark the location of the bracket on the vehicle before pulling it out. You have to access the transaxle on the rear of the cart and pull out the bracket where the cables are attached. With the Yamaha G2, the shift cable adjustment is not a very difficult one. You can email them your requirement and if you are lucky, you may get it. The manufacturer may be carrying this part. If you can’t find the original bracket, search on sites like eBay and you may be able to locate one. You will still need to make some fine adjustments to the shift cable after fixing the bracket. If you can find that, the shift cable adjustment becomes a breeze. With the Gas model of E-Z-GO golf cart, the issue of the shift cable adjustment can be sorted by sourcing the original cable bracket that comes with the cart, when new. Check if the belt is of the right size in the E-Z-Go Workhorse as well. The thing to remember here is to keep the shift position in neutral while making the adjustment. The other option is to change the shift cable itself completely. The cable needs to be moved up by 1 3/8-inch. The simple solutions offered for the Workhorse are the same as for the other models like TXT. The company may have to step in and post the solution along with a diagram so that the cart users can benefit. Users have written about the shift cable adjustment not working even after several tries. The E-Z-GO Workhorse model also poses a similar situation where the shift jams up and can’t be used for reversing the cart. Belts with shorter lengths can be fitted to see if it solves the issue. Some people removed the belt and say the shift worked fine afterward. You can also check if the belt is of the right length. The belt has been seen as one possible reason for the shift not moving freely. Some EZGO owners have experienced the shift working in one direction and not the other. In both these cases, based on the information available from the vehicle manufacturer and the users of the carts, the access to the cable location and making the changes needed are a little tough. The other is you are trying to make some minor adjustments so that it functions properly and allows you to shift forward and reverse. One is fixing a new set of cables for the E-Z-GO RXV cabling for the shift. You will have to include the thickness of the nut for this measurement. The play given is 1 3/8-inch and it goes till the end of the threaded portion. Keep the shift in neutral and then adjust the cable. There’s a certain level of tightness about them and you would want to tighten the cable accordingly. The important point to note here is that the shifting forward and reverse in these golf carts do create trouble sometimes, particularly on slopes. You will have to go by the suggestions from those who have actually made the adjustments in their carts. There’s very little available by way of printed literature on the step-by-step method of adjusting the shift cable on the E-Z-GO TXT model. The adjuster has to be in the neutral position while making this change in the cable’s position. Yamaha G20 Golf Cart Shift Cable AdjustmentĪt times, the cable connecting the forward-reverse shift in the E-Z-GO golf cart may need adjustments that are a little tough to carry out without a proper manual or instructions.Ī golf cart shift cable adjustment is 1 3/8-inch from the washer and is to be made till the end of the threads.Yamaha G16 Golf Cart Shift Cable Adjustment.Yamaha G9 Golf Cart Shift Cable Adjustment.E-Z-GO Workhorse Shift Cable Adjustment.How to Adjust Shift Cable on a Golf Cart.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |